Short answer
If your stapler cannot reach the center of your open zine, many standard staplers can be opened flat (so the head and base lie in a line). You then press the staple through the zine’s fold from the outside into a soft surface, and fold the staple legs over by hand. If that does not work for your stapler, sewing the fold with thread (a pamphlet stitch) gives a similar result without any staples.
Why a regular stapler struggles
A zine is stapled in the middle of an open sheet. A standard stapler has a short throat, so it can only reach the edge of the paper. A half-letter zine opened out is about 11 by 8.5 inches, so the center fold is about 5.5 inches from the edge and typically out of range for a desk stapler.
Method 1: open a standard stapler flat
Many desktop staplers have a hinge that opens to 180 degrees, so you can use the stapler like a stamp. Check yours before trying this.
- Fold and nest your sheets, with the cover outermost, and crease the spine.
- Mark the staple positions along the fold. Two evenly spaced marks is typical for a small zine.
- Open the zine flat with the outside of the cover facing up, and place it on a soft surface such as a folded towel, a piece of cardboard, cork board, or a thick stack of scrap paper.
- Open the stapler so that the base swings away. Many staplers have a pin or catch to hold it in the flat position.
- Press the stapler head down firmly at each mark. The staple should go through all the layers and into the soft surface. The staple legs will not fold on their own because there is no anvil.
- Lift the zine and look at the inside. The staple legs will stick up. Bend them flat toward each other, or in the direction of the fold, with a bone folder, the back of a spoon, or a flat-ended tool.
- Close the zine and run a bone folder along the spine to flatten it.
Some staplers have an anvil that can be rotated so the legs bend outward (a “pin” mode) or inward (“clinch” mode). This can make step 6 easier. Check your stapler’s instructions.
Method 2: staple the sheets before the final fold
For thin zines, it may be simpler to staple while the sheets are still flat, if the stapler can reach the position you need. Mark the fold line, then staple on that line, and then fold. This only works when the staple location is within the throat depth, which is not the case for most full-size sheets. It may work for smaller zine formats, such as a quarter-letter zine folded from a sheet cut to size.
Test on scrap paper first, because staples placed on the fold line can tear paper when folded.
Method 3: side-stapling and other alternatives
- Pamphlet stitch with thread: Sew along the fold with a needle and thread. It looks handmade and does not need any special tool. See stapled and pamphlet-stitched zines for the steps.
- Stab binding: Punch holes along the spine margin and sew through them. This is more of a different binding style than a substitute, but it works with any thickness the needle can pass through.
- Borrow or use one: Libraries, schools, offices, print shops and community zine spaces often have a long-reach stapler available.
- Print shop finishing: Many print shops will saddle-stitch for a small fee, and can handle larger batches.
You can compare these with other binding methods in how to bind a zine.
Tips and safety
- Staples are sharp. Keep fingers clear of the stapler head, and press the legs flat so they will not scratch readers.
- Practice on scrap paper first. The first few staples are usually messy.
- Use staples sized for the thickness of the stack. If the legs are too short to go through, the staple will not hold.
- Stack the sheets as flat as possible, since a bulging fold makes the flat method harder.
- Cover the spine with washi tape if you want a cleaner finish.
Troubleshooting
- The staple will not penetrate. The stack may be too thick, or the stapler too weak. Use fewer sheets or switch to thread.
- The legs will not bend. Use a firmer surface under the zine to bend against, or use a tool with a flat end.
- The staple is crooked. Mark the position and hold the stapler square, pressing straight down.
- The zine will not close flat. Press along the spine with a bone folder, and check that the legs are fully flattened.
For the folding part, see how to fold a zine.