What Coptic stitch is
Coptic stitch is a hand-sewing method in which several folded sections (signatures) are sewn together with a chain-like stitch along the spine. Each signature is sewn through its own fold and then linked to the signature next to it. The thread is exposed, there is no glue, and the finished book opens flat. The method is named after the Coptic codices of early Christian Egypt, though modern versions vary.
Why use it for a zine
- It opens flat, which is good for art zines, sketchbooks and journals.
- It handles more pages than a simple staple or pamphlet stitch, since the zine is made of several smaller signatures instead of one thick fold.
- It needs no glue or machinery.
- The visible stitching looks decorative.
It is slower than stapling and requires care to get the thread path right, so it is best for special editions, gifts and personal projects. For a faster option, see stapled and pamphlet-stitched zines.
Materials
- Sheets of paper for signatures, folded in half
- Cover material: heavy cardstock, thin board or similar
- Waxed linen thread (or another strong thread, waxed with beeswax)
- A needle with a blunt tip and a large enough eye, such as a tapestry needle
- An awl and a scrap board
- A bone folder
- A ruler, pencil and binder clips
- A hole template made from a strip of card (optional but useful)
Prepare signatures and covers
- Fold the sheets in half with the bone folder. Nest a few folded sheets together to form each signature. Four to six sheets per signature is a common range, but this depends on paper weight. Heavier paper means fewer sheets.
- Make several signatures, all the same size and thickness. A zine might have three to six.
- Cut two covers the same height as the signatures and slightly wider than the folded width, so that they overhang the pages a little.
Mark and punch the holes
- Make a template. On a strip of card the height of the signature, mark the first and last holes a short distance in from the head and tail (around 1 cm is common), with the remaining holes evenly spaced between. Four holes (called stations) is a good number for a small zine.
- Punch the signatures. Open each signature to the center fold and punch through the fold at each mark, using the template as a guide.
- Punch the covers. The cover holes sit along the spine edge, at the same stations, and in from the edge by a small, consistent distance (a few millimeters to a centimeter).
Sew step by step
The following gives the general thread path. Details differ between tutorials, so treat this as an outline and keep your thread path consistent.
- Cut thread to a generous length, because the thread is used for the whole book. Many makers allow several times the length of the entire spine, multiplied by the number of signatures. It is better to start with a thread that is too long than to run out and add more. Thread the needle and make a stopper knot at one end, or leave a tail.
- Stack your pieces with the back cover first and the first signature on top, with the cover’s hole edge at the spine.
- Attach the first signature to the cover. Starting inside the signature at the head station, push the needle out through the hole in the signature fold and through the matching hole in the cover. Wrap the thread around the cover’s spine edge, and go back in through the same holes (or into the signature hole), then continue to the next station inside the signature. Repeat at each station, so each stitch hooks around the cover’s spine edge. Finish with the thread exiting at the last station, with a tail left at the beginning to tie off later.
- Add the second signature. Place it on top of the first. Go into its last station from outside to inside, run the thread inside the fold to the next station, and come out.
- Link the signatures. At each station, where the thread exits the new signature, pass the needle under the connecting stitch between the signature below and the cover (or, later, between the two signatures below), pull the thread so it makes a small chain link, and re-enter the same hole in the new signature.
- Continue along the signature, so that at each station you link around the stitch below before entering the next.
- At the end of the signature, make a stitch to hold the last link, then place the next signature on top and repeat the process in the opposite direction.
- Repeat for each signature. When you reach the last one, attach the front cover in the same way as the back cover.
Each time you pull the thread, keep a steady, even tension. Too tight will tear the paper, and too loose will leave gaps.
Finish and tie off
After the final station, make a few loops around the thread at the end of the chain, or tie a small knot (a kettle stitch). Tie the tail at the beginning to the first stitch. Trim the thread, leaving a few millimeters. A dab of glue on the knot is optional.
Troubleshooting
- Gaps in the spine. The thread is too loose, or the holes are too far from the fold.
- Signatures sit uneven. Holes are not at the same height. Use a template for every signature.
- Torn paper at the holes. Thread is too tight or the paper too thin. Use a reinforcing strip inside the fold if needed.
- Thread tangles. Keep the thread waxed and let the needle hang to untwist occasionally.
- Running out of thread. Tie on a new length with a small knot, hidden inside a signature.
Variations
- Different numbers of stations, more for taller books.
- Hard covers, using thin board wrapped in paper or fabric.
- Colored thread, to make the chain a design feature.
If you want a simpler sewn spine, look at what the Japanese binding method is, and for a comparison of all the options see how to bind a zine.