What an accordion zine is
An accordion zine, also called a concertina zine, is a strip of paper folded back and forth in a zigzag. Each section between folds is a panel. The zine stands up like a small screen when you open it, and it can be pulled out to show every panel at once, or closed to a compact stack.
There is no spine and no staples, and the number of panels is up to you. That makes it a good fit for:
- Comics and sequences that read left to right
- Panoramic photos or drawings that continue across panels
- Timelines, maps and step-by-step guides
- Poems with a visual rhythm
It is also one of the few formats where the “page count” doesn’t need to be a multiple of four. See how many pages a zine should have for the rule that applies to other formats.
What you need
- Paper (printer paper works; slightly heavier paper holds its shape better)
- A ruler and pencil
- Scissors or a craft knife and cutting mat
- Glue stick or double-sided tape (for joining strips or adding covers)
- A bone folder or the edge of a ruler for sharp creases
- Optional: thicker card for covers, and a rubber band or ribbon to hold it closed
Step by step: a four- or eight-panel accordion
This version uses one or two strips cut from a sheet, so you need no gluing for the smallest size.
- Cut the strip. For a letter sheet in landscape (11 inches wide, 8.5 inches tall), cut it in half across the short direction to get two strips each about 4.25 inches tall and 11 inches long. Use one strip. (On A4, the strips are about 105 mm tall and 297 mm long.)
- Fold in half. Bring the short ends together and crease. Unfold it again.
- Fold each end to the center crease. Bring each end in to meet the middle crease, and crease. You now have four equal panels. Each panel on a letter strip is about 2.75 inches wide.
- Make the creases alternate. Turn the strip so that folds alternate between mountain (peak) and valley (dip). The center fold goes one way, and the outer folds go the other way. This is what creates the zigzag.
- Pleat it. Pinch the creases together and flatten the strip into a stack. It should pop open as a zigzag.
To make eight panels from the same strip, fold it in half three times rather than twice, then unfold and re-crease so the folds alternate. Panels become narrower, about 1.4 inches wide on a letter strip, so keep the content simple.
Making a longer accordion by joining strips
If you need more panels, join two or more strips.
- Cut strips of the same height. Fold each strip into panels as above.
- Decide where to join. A good join is at a fold, so that the panels continue without a visible gap.
- Add a narrow tab: leave a strip of about half an inch on the end of one piece, or cut a separate small piece to use as a tab. Glue it to the back of the panel on the next strip. Let it dry flat under a heavy book.
- Check that the alternating mountain and valley folds continue across the join.
Another option is to print or draw on one long continuous strip of paper if you have access to a roll or wide-format printing.
Adding covers
A cover isn’t required, but it protects the zine and gives it an identity.
- Cut two pieces of thicker card or heavy paper slightly larger than your panel size, or the same size for a tidy look.
- Glue one piece to the first panel’s back and the other to the last panel’s back.
- If you want to close the zine, attach a ribbon or elastic band to the back cover, or slide a paper band around it.
If you don’t add covers, make the first and last panels carry the title and a short closing line.
Laying out the panels
You have two options:
- One side only. Plan all your panels on the front of the strip. Everything reads left to right when you open it. This is easier to print and cut, and works well for panoramas and comics.
- Both sides. The back of each panel is also available, so you can plan two “runs”: one on the front and one on the back. This doubles the content, but alignment needs care, and for double-sided printing you need to know which way your printer flips the page. Do a test print on scrap paper.
For both options, remember:
- Keep important text and faces away from the folds.
- Check which panels end up facing each other when the zine is half-open.
- Number the panels on a mock-up before final art.
If you are laying out images that span several panels, remember that each fold can break an image. This is part of the charm, but plan where cuts in the picture will fall. For a longer photo sequence, see how to make a photo zine.
Content ideas
- A walk, route or day told as a continuous scene
- A single drawing that stretches across all panels
- A step-by-step guide, one step per panel
- A comic with one beat per panel (also see how to make a mini comic zine)
- A list, poem or alphabet
- A set of photos that become a panorama when opened
Troubleshooting
- Folds don’t line up. Measure and mark the strip before folding, and crease with a ruler rather than by eye.
- It won’t stay closed. Add a band, ribbon, or a cover with a closure.
- Paper cracks at folds. Use thinner paper, or score the fold with a bone folder or the back of a knife before folding. Printed ink can crack on heavy paper.
- Panels bend. Use heavier paper for covers, or glue a piece of card behind each panel.
For other formats and sizes to try, see types of zine formats, or compare other zine folding techniques.