Layout and Design

Zine Margins, Gutters and Bleed: Setting Up Your Pages Correctly

Set up zine margins, gutters and bleed correctly: what each term means, when you need bleed, starting values, home printer limits and how to check your file.

On this page
  1. Margins, gutters, bleed and the safe zone
  2. Do you even need bleed?
  3. Recommended starting values
  4. The gutter and binding
  5. Home printers and copiers
  6. Set it up in common tools
  7. Check your file before printing
  8. Common mistakes

Margins, gutters, bleed and the safe zone

These four terms cause most of the confusion when setting up a zine.

  • Trim size: the final size of a page after it has been folded and, if needed, trimmed.
  • Margin: the empty space between your content and the trim edge. It keeps text and key images from being clipped.
  • Gutter (or inner margin): the space near the spine, where pages are folded or stapled. In a booklet the inside margin is often larger than the outside to compensate for the fold. Some software also uses “gutter” to mean the space between columns, so check which one a dialog means.
  • Bleed: extra artwork that extends beyond the trim edge, so that colour or images reach the edge of the page after cutting, with no thin white line.
  • Safe zone: the area inside the margins where important content (text, faces, logos) should stay.

Do you even need bleed?

It depends on how you’re printing.

  • Bleed is needed when a background colour or image runs to the very edge of the page and the pages are cut to size by a printer. Print shops commonly ask for bleed on the outer edges of artwork.
  • Bleed is not needed if your design has a white (paper-coloured) background and nothing touches the edge. A slight cutting shift won’t show on white paper.
  • Bleed usually doesn’t apply to home printing or most photocopying, because those machines generally can’t print to the very edge of the paper anyway. In that case, design with a clear white border and skip bleed.

If you are sending files to a professional printer, ask for their template and specifications before you start. Requirements vary.

These are common starting points, not universal rules. Adjust them after test printing and follow your printer’s guidance.

Setting Typical starting value
Bleed (professional printing) 0.125 in (1/8 in) or 3 mm on each outside edge
Safe zone / outside margin Around 0.25 in (6 mm) inside the trim, more for home printing
Inside margin (gutter) Larger than the outside margin; increase for thick booklets
Copier-friendly border Roughly 0.25 to 0.5 in around content

Library zine guides give slightly different numbers: one suggests leaving about half an inch around content because photocopiers may cut off material near the edge, while another suggests a quarter-inch margin. The right figure depends on the machine, so test it.

To make a file with bleed, add the bleed to the page size. A common rule is to add twice the bleed to both width and height, for example 0.25 in extra for a 0.125 in bleed. A 5.5 x 8.5 in page with bleed becomes 5.75 x 8.75 in. Most layout programs handle this for you through a bleed field.

The gutter and binding

When a booklet is folded and stapled, the inner edge of each page curves into the spine and part of it is hidden. If your inside margin is too small, text gets close to the fold and is hard to read. The thicker the booklet, the more of the inner edge disappears.

Practical steps:

  • Make the inside margin bigger than the outside margin.
  • Keep text and important images away from the fold, and avoid putting a face or key lettering across the centre of a spread.
  • For stapled booklets with many sheets, the inner pages tend to stick out slightly further than the outer ones when folded. This can mean the outside edges need trimming, which makes outer margins narrower on the inner pages. Leave a little extra room, and test-assemble a copy.
  • For single-sheet eight-page zines, panels meet at folds on several sides, so keep an even margin inside every panel.

Home printers and copiers

  • Most home printers have an unprintable margin around the edge, often around a quarter inch. Check your printer’s specifications or print a test grid.
  • Some printers offer a borderless option, but results vary and it can crop your page. Test before relying on it.
  • Photocopiers can clip content near the edge. A border of about a quarter to half an inch gives you room.
  • Scaling matters. When you print, choose actual size or 100%. “Fit to page” can shrink your margins and change the layout.
  • Double-sided printing can shift the position of the back side slightly, so don’t place a tight design element that needs to line up exactly on both sides.

For more on page layout, see the zine layout guide.

Set it up in common tools

  • InDesign: enter margins and bleed in the New Document dialog. Export with Use Document Bleed Settings turned on. See how to make a zine in InDesign.
  • Affinity Publisher: set margins in Document Setup, with inside and outside margins when facing pages are on, and set bleed in the same dialog. See making a zine in Affinity Publisher.
  • Canva: guides help with margins, and options to show print bleed are available when preparing a print PDF, depending on your design and plan. See does Canva do zines?
  • Microsoft Word: Word has margins and a gutter setting but no true bleed option. To fake bleed you need to enlarge the page and stretch graphics. See how to make a zine in Word.
  • Google Slides: you can use guides for margins, but there’s no bleed setting. See how to make a zine in Google Slides.
  • Procreate: build the bleed into the canvas size yourself. See how to make a zine in Procreate.

Check your file before printing

  • Is the page size correct for your format?
  • Is any background colour or image extended into the bleed (if bleed is needed)?
  • Is all text well inside the safe zone and away from the fold?
  • Is the inside margin bigger than the outside margin?
  • Do your exported pages include or exclude bleed as your printer requested?
  • Does your PDF show the bleed area when you check it in a PDF viewer?
  • Have you printed a test copy at 100% scale and held it up to a light or folded it to check edges?

Common mistakes

  • No bleed on a full-colour edge: a thin white line appears where the trim is slightly off.
  • Text too close to the edge: it may be clipped by the printer or the cutter.
  • Equal margins on all sides in a thick booklet: text near the spine is hard to read.
  • Scaling the page when printing: this changes your carefully planned margins.
  • Skipping the test print: the simplest way to avoid expensive mistakes is to print one copy first.

The complete guide to layout and design

Zine Layout and Design: How to Get the Zine Look
Read the guide

Keep exploring

Guides from other topics

All topics →